I will never ever ever EVER wait this long between blog posts again! Oh my! Just trying to organize the photos over the last couple of weeks has been an absolute nightmare! Then, to top things off, I accidentally deleted half of the pics I wanted to show you guys before I even got them up on the blog 😦 major bummer!

But, never fear, I will press forward!…and you will have to rely on my imaginative descriptions as opposed to the colorful pictures for the next couple of posts!

If you will recall, the last time I wrote about the bathroom in our house we had just hung cement board in the shower and were ready to install new plumbing and tile on the shower walls.

Before we could proceed we had to install the new bathroom fan. The job required a little work from the outside, too 😉

I’m glad that job fell to my dad! That’s too far up there for me!

After the fan was installed (a $30 clearance item at Menard’s by the way!!), we were ready to start mixing the thin set for the tiles.

When you consider the powdery substance that must be mixed with water by a giant attachment to the drill that looks curiously like a hand mixer…well, making up a batch of thinset ain’t a whole lot different than baking a cake! And if there’s one thing I love to do, it’s bake a cake 😉

The consistency of this stuff is a bit different though. Oh! And I learned a few tiling jobs back to always wear gloves (latex, in my case) before attempting this project. If you don’t your hands and nails will be ruined for at least a couple of days! Also, remember to mix the thinset in small quantities- especially if you are not that talented at laying tiles. This stuff tends to dry out pretty quickly.

We were lucky in that my dad was mixing thinset as well as cutting tiles while my friend Phil and I laid the actual tiles on the wall of the shower.

With three people helping the job went fairly fast although we did run into some problems when we were adding a strip of mosaic tile and also when we inserted the ceramic soap dish and corner shelf. The shelves were pretty heavy to be supported by the thinset and so we had to rig some temporary support systems. We also ran into a problem where the large 12×12 tiles were sliding into the mosaic tiles (stupid gravity!) and pushing everything out of place. We finally solved the problem by creating spacers out of paint stirrers (who woulda thunk?!) and waiting until the mosaic tiles had completely dried in place before adding any 12×12 tiles above them.

The next step was to waiting for everything to dry properly. Then, the blue spacers could be removed and grout could be applied to fill the cracks between the tiles.

Grouting is a super easy process that works best with two people. When my dad and I are working together, he smears the grout into place and I follow behind with many, many clean rags to wipe off all of the excess. It is a dirty process but it certainly pulls the look of the tile together.

Check out a couple close ups of the finished product!

Meanwhile, we were also working on revamping the vanity. Raul and I decided to keep the granite-ish countertop but the factory finish oak cabinets had to go! Instead of purchasing new cabinets I did a lot of research about how to paint cabinets. All the forums raved about Advance paint from Benjamin Moore which is a latex paint which basically acts like an oil based paint without all the negatives. I scooped a can of the stuff and started on my project. The first step was detaching all the doors and drawer faces. I removed all of the hardware and then filled in all the holes with woodfiller. A couple of sandings later and voila!- I was ready to prime.

We opted to spray the cabinet faces rather than brush or roll them in order to get a smoother finish and avoid any marks.

We sprayed on one coat of Killz primer and let them dry for a couple of days due to the high humidity in the basement. Then, it was time to try the magic Benjamin Moore paint. I picked a color somewhere in between blue, green, and gray that went really well with the countertop as well as the tiles on the shower walls and floor.

We ended up spraying the cabinets twice in order to get a nice even coverage. When everything was good and dry we updated the look with some new brushed nickel hardware. Everything I read recommended that we let the cabinet faces sit for a week or two before installing them back on the vanity in order to avoid and nicks.

Once we got everything back in place the vanity looked completely different!

After a ridiculously long and tedious process of mudding, sanding, and repeating, we were able to not only finish out the tile on the floor using the same process, but also apply a couple of coats of light greyish tan paint to the walls- “Colonial Gray” to be exact, a historical color from Valspar 😉

It was also time to add a new shower faucet. I got a really cool set online for a great price. It’s design was also made to look vintage-y which was something I wanted to maintain as much as possible in this brand new bathroom.

We decided to go ahead and replace the toilet in the bathroom as well (Why the hell not?!) and I got a great deal on one of those water saving toilets. You know one of those with one button for liquids and one for solids? 🙂

We also decided to fill in the area where the medicine cabinet used to be with the same mosaics that we used as an accent in the shower. Now we have a pretty cool little niche in the bathroom.

I think it would make a perfect home for a beta fish, don’t you? Entertainment while you sit on the loo! 😉

We got two mirrors with vintage stylings to hang over the double sinks and added a temporary mini blind for privacy until I can decide on curtains (hey! that’s a really big decision!)

We also decided to refrain from installing shower doors for right now. We got a cool shower curtain from Target that will work fine for the next couple of months though I definitely want to add clear shower doors eventually.  All that’s left to do in the bathoom is add the molding and find some cool shelves for between the mirrors.

I love our new bathroom!